Lee Two-Cavity Bullet Mold for .30 Caliber Reloading Applications.
Precision-engineered to produce .309 inch diameter bullets weighing approximately 113 grains, featuring a Flat Nose (FN) profile optimized for Gas-Check applications.
Ballistic Coefficient (BC) of .199 ensures enhanced aerodynamic stability and improved downrange performance for metallic and semi-metallic projectiles.
Lees two-cavity bullet molds represent an excellent value proposition for precision handloaders and ballistic enthusiasts seeking high-quality bullet casting tools at a cost-effective price point.
Constructed from corrosion-resistant aluminum alloy, these molds offer superior durability and longevity in demanding reloading environments.
Aluminum molds exhibit rapid thermal conductivity, allowing for faster heat absorption and dissipation compared to traditional iron or steel molds, which translates into increased casting efficiency and reduced cycle times.
Due to their efficient thermal properties, bullet casters can begin accumulating consistent, high-quality projectiles after casting only a minimal number of rounds.
Weighing approximately one-third less than equivalent iron or steel molds, these lightweight aluminum molds significantly reduce operator fatigue during extended casting sessions.
The mold halves are securely fastened with robust wooden-handled clamps, ensuring precise alignment and consistent bullet dimensions throughout the casting process.
Note that bullet weights may exhibit slight variations depending on the specific lead alloy composition utilized during casting.
Equipped with an integrated sprue cutter blade, the mold facilitates clean and efficient lead flow control, enabling easy release of finished bullets with minimal post-casting cleanup.
Includes durable wooden-handled sprue plate tongs for safe and ergonomic operation.
For optimal mold performance and bullet quality, it is highly recommended to thoroughly degrease the mold prior to initial use. Additionally, seasoning the mold by applying smoke or a specialized mold treatment product will enhance bullet release and extend mold life.
Under no circumstances should the interior cavity surfaces be lubricated, as this can adversely affect bullet integrity and mold longevity.
Lightly lubricate the sprue plate retaining screw to ensure smooth operation and prevent seizing during repetitive casting cycles.
Mold C309-113-F for Precision Hunting and Reloading Bullets
90362
Lee Two-Cavity Bullet Mold for .30 Caliber Reloading Applications.
Precision-engineered to produce .309 inch diameter bullets weighing approximately 113 grains, featuring a Flat Nose (FN) profile optimized for Gas-Check applications.
Ballistic Coefficient (BC) of .199 ensures enhanced aerodynamic stability and improved downrange performance for metallic and semi-metallic projectiles.
Lees two-cavity bullet molds represent an excellent value proposition for precision handloaders and ballistic enthusiasts seeking high-quality bullet casting tools at a cost-effective price point.
Constructed from corrosion-resistant aluminum alloy, these molds offer superior durability and longevity in demanding reloading environments.
Aluminum molds exhibit rapid thermal conductivity, allowing for faster heat absorption and dissipation compared to traditional iron or steel molds, which translates into increased casting efficiency and reduced cycle times.
Due to their efficient thermal properties, bullet casters can begin accumulating consistent, high-quality projectiles after casting only a minimal number of rounds.
Weighing approximately one-third less than equivalent iron or steel molds, these lightweight aluminum molds significantly reduce operator fatigue during extended casting sessions.
The mold halves are securely fastened with robust wooden-handled clamps, ensuring precise alignment and consistent bullet dimensions throughout the casting process.
Note that bullet weights may exhibit slight variations depending on the specific lead alloy composition utilized during casting.
Equipped with an integrated sprue cutter blade, the mold facilitates clean and efficient lead flow control, enabling easy release of finished bullets with minimal post-casting cleanup.
Includes durable wooden-handled sprue plate tongs for safe and ergonomic operation.
For optimal mold performance and bullet quality, it is highly recommended to thoroughly degrease the mold prior to initial use. Additionally, seasoning the mold by applying smoke or a specialized mold treatment product will enhance bullet release and extend mold life.
Under no circumstances should the interior cavity surfaces be lubricated, as this can adversely affect bullet integrity and mold longevity.
Lightly lubricate the sprue plate retaining screw to ensure smooth operation and prevent seizing during repetitive casting cycles.
€50.52
Tax included
Related Products
- Out-of-Stock
- Out-of-Stock
