Lee Two-Cavity Mold for 8x56mm Rimmed Hungarian Caliber
Precision-engineered to cast bullets with a diameter of .329 inches, this mold produces projectiles weighing approximately 205 grains, featuring a 1R groove designed specifically for Gas-Check applications.
Boasting a ballistic coefficient of .361, these bullets are optimized for enhanced external ballistics, providing superior stability and accuracy at extended ranges.
Lees two-cavity molds represent an excellent choice for metallic reloaders and precision shooters seeking high-quality bullet molds at a cost-effective price point without compromising performance.
Constructed from corrosion-resistant aluminum alloy, these molds offer exceptional durability and longevity in demanding reloading environments, resisting oxidation and wear over time.
Aluminum molds efficiently absorb and dissipate heat faster than traditional iron or steel molds, significantly reducing cycle times during casting and improving workflow efficiency.
Reloaders can begin accumulating consistent, high-quality projectiles after casting just a few rounds, ensuring immediate usability and reliability in the field or on the range.
Weighing approximately one-third less than comparable iron or steel molds, these lightweight aluminum molds reduce operator fatigue during extended casting sessions, enhancing comfort and control.
The mold halves are securely clamped together using robust wooden-handled tongs, ensuring precise alignment and tight closure to minimize flash and maintain bullet integrity.
Note that indicated bullet weights may vary slightly depending on the specific lead alloy composition used during casting, affecting density and final mass.
Equipped with a practical integrated sprue cutter, this mold facilitates clean separation of molten lead runners, allowing for smooth ejection of finished bullets and minimizing post-cast cleanup.
Included with the mold are high-quality tongs designed for safe and ergonomic handling throughout the casting process.
For optimal performance and mold longevity, it is highly recommended to thoroughly degrease the mold prior to initial use. Additionally, seasoning the mold by applying a light coat of mold release agent or fumigating with recommended products will improve bullet release and extend mold life.
Mold C329-205.1R (8x56) for Precision Bullet Casting and Reloading
90775
€50.52
Tax included
Lee Two-Cavity Mold for 8x56mm Rimmed Hungarian Caliber
Precision-engineered to cast bullets with a diameter of .329 inches, this mold produces projectiles weighing approximately 205 grains, featuring a 1R groove designed specifically for Gas-Check applications.
Boasting a ballistic coefficient of .361, these bullets are optimized for enhanced external ballistics, providing superior stability and accuracy at extended ranges.
Lees two-cavity molds represent an excellent choice for metallic reloaders and precision shooters seeking high-quality bullet molds at a cost-effective price point without compromising performance.
Constructed from corrosion-resistant aluminum alloy, these molds offer exceptional durability and longevity in demanding reloading environments, resisting oxidation and wear over time.
Aluminum molds efficiently absorb and dissipate heat faster than traditional iron or steel molds, significantly reducing cycle times during casting and improving workflow efficiency.
Reloaders can begin accumulating consistent, high-quality projectiles after casting just a few rounds, ensuring immediate usability and reliability in the field or on the range.
Weighing approximately one-third less than comparable iron or steel molds, these lightweight aluminum molds reduce operator fatigue during extended casting sessions, enhancing comfort and control.
The mold halves are securely clamped together using robust wooden-handled tongs, ensuring precise alignment and tight closure to minimize flash and maintain bullet integrity.
Note that indicated bullet weights may vary slightly depending on the specific lead alloy composition used during casting, affecting density and final mass.
Equipped with a practical integrated sprue cutter, this mold facilitates clean separation of molten lead runners, allowing for smooth ejection of finished bullets and minimizing post-cast cleanup.
Included with the mold are high-quality tongs designed for safe and ergonomic handling throughout the casting process.
For optimal performance and mold longevity, it is highly recommended to thoroughly degrease the mold prior to initial use. Additionally, seasoning the mold by applying a light coat of mold release agent or fumigating with recommended products will improve bullet release and extend mold life.
Related Products ( 16 other products in the same category )
