- Out-of-Stock
Lee Two-Cavity Mold for .44 Magnum and .44 Special Calibers
Precision-engineered with a .430 inch diameter and designed to cast bullets weighing approximately 310 grains, this Lee mold features a gas-check style (RF) base, optimized for metallic and semi-metallic reloading applications.
Boasting a ballistic coefficient (BC) of .218, these bullets offer reliable external ballistics performance for both hunting and target shooting disciplines.
Lees two-cavity molds represent an excellent balance between quality craftsmanship and cost-efficiency, making them a preferred choice among handloaders and bullet casters who demand consistent bullet dimensions without breaking the budget.
Constructed from high-grade aluminum alloy, these molds provide superior corrosion resistance compared to traditional iron or steel molds, ensuring longevity and reliable performance in diverse environmental conditions.
The aluminum composition allows for rapid thermal transfer, enabling the mold to heat up and cool down significantly faster than heavier iron or steel variants. This thermal efficiency reduces cycle times during bullet casting, increasing overall productivity.
Due to the molds efficient heat management and precise cavity design, casters can begin accumulating quality projectiles after producing just a few rounds, facilitating early-stage inventory buildup for reloading sessions.
Weighing approximately one-third less than comparable iron or steel molds, this lightweight design minimizes operator fatigue during extended casting sessions, enhancing comfort and control.
The mold halves are securely clamped together using robust wooden-handled tongs, ensuring tight cavity alignment and consistent bullet profiles with each pour.
It is important to note that the bullet weights produced may exhibit slight variations depending on the specific lead alloy composition used, necessitating careful alloy selection and consistency for precision reloading.
An integrated sprue cutter blade serves as an efficient lead gate, facilitating clean separation of the cast bullets from the mold and minimizing post-casting cleanup.
The mold package includes high-quality tongs for safe and ergonomic handling during the casting process.
For optimal mold performance and bullet quality, it is highly recommended to thoroughly degrease the mold prior to initial use. Additionally, seasoning the mold by applying a recommended mold release agent or smoke treatment will enhance bullet release and extend mold life.
Mold C430-310-RF for Precision Reloading and Hunting Bullets
90858
Lee Two-Cavity Mold for .44 Magnum and .44 Special Calibers
Precision-engineered with a .430 inch diameter and designed to cast bullets weighing approximately 310 grains, this Lee mold features a gas-check style (RF) base, optimized for metallic and semi-metallic reloading applications.
Boasting a ballistic coefficient (BC) of .218, these bullets offer reliable external ballistics performance for both hunting and target shooting disciplines.
Lees two-cavity molds represent an excellent balance between quality craftsmanship and cost-efficiency, making them a preferred choice among handloaders and bullet casters who demand consistent bullet dimensions without breaking the budget.
Constructed from high-grade aluminum alloy, these molds provide superior corrosion resistance compared to traditional iron or steel molds, ensuring longevity and reliable performance in diverse environmental conditions.
The aluminum composition allows for rapid thermal transfer, enabling the mold to heat up and cool down significantly faster than heavier iron or steel variants. This thermal efficiency reduces cycle times during bullet casting, increasing overall productivity.
Due to the molds efficient heat management and precise cavity design, casters can begin accumulating quality projectiles after producing just a few rounds, facilitating early-stage inventory buildup for reloading sessions.
Weighing approximately one-third less than comparable iron or steel molds, this lightweight design minimizes operator fatigue during extended casting sessions, enhancing comfort and control.
The mold halves are securely clamped together using robust wooden-handled tongs, ensuring tight cavity alignment and consistent bullet profiles with each pour.
It is important to note that the bullet weights produced may exhibit slight variations depending on the specific lead alloy composition used, necessitating careful alloy selection and consistency for precision reloading.
An integrated sprue cutter blade serves as an efficient lead gate, facilitating clean separation of the cast bullets from the mold and minimizing post-casting cleanup.
The mold package includes high-quality tongs for safe and ergonomic handling during the casting process.
For optimal mold performance and bullet quality, it is highly recommended to thoroughly degrease the mold prior to initial use. Additionally, seasoning the mold by applying a recommended mold release agent or smoke treatment will enhance bullet release and extend mold life.
€50.52
Tax included
Related Products
- Out-of-Stock
- Out-of-Stock
.jpg)
- Out-of-Stock