LEE TL 2-Cavity Mold specifically engineered for precision casting of .38 Special, .357 Magnum, and .38 Colt New Police caliber bullets. This mold is designed to deliver consistent performance and accuracy for handloaders and ballistic enthusiasts focused on metallic and semi-metallic projectile manufacturing.
Featuring a .358 inch diameter and producing 158-grain 2-Ring Ogival bullets, this mold is optimized for the .38 Special, .357 Magnum, and .38 Colt New Police cartridges, ensuring optimal ballistic coefficients and terminal performance for both target shooting and hunting applications.
Each cavity incorporates a finely engineered micro-groove rifling to enhance bullet lubrication retention, reducing barrel leading and improving overall accuracy during firing cycles.
LEEs 2-cavity molds represent an excellent balance between cost-efficiency and high-quality craftsmanship, making them a preferred choice among precision reloaders and ballistic technicians seeking reliable bullet molds without compromising on durability.
Constructed from corrosion-resistant aluminum blocks, these molds offer superior thermal conductivity compared to traditional iron molds, allowing for faster heat transfer during the casting process. This results in reduced cycle times and improved bullet consistency.
Aluminum mold blocks also weigh approximately one-third less than their iron or steel counterparts, significantly reducing operator fatigue during extended casting sessions and enhancing overall handling ergonomics.
The two halves of the mold are securely clamped together using robust wooden-handled tongs, ensuring zero cavity movement during molten metal pouring and solidification, which is critical for maintaining bullet dimensional integrity and surface finish.
Note that bullet weights may vary slightly depending on the specific lead alloy composition used, allowing reloaders to fine-tune projectile mass to their ballistic requirements.
The included tongs feature ergonomic wooden grips for safe and comfortable handling during high-temperature casting operations.
An integrated, practical sprue cutter blade is incorporated to efficiently sever the lead sprue, facilitating smooth release of fully formed bullets and minimizing post-casting cleanup.
For optimal mold longevity and bullet quality, it is highly recommended to thoroughly degrease the mold before initial use and periodically apply a recommended mold seasoning agent or smoke treatment to enhance release properties.
Never lubricate the interior cavity surfaces of the mold, as this can negatively affect bullet surface finish and dimensional accuracy.
Lightly lubricate the sprue cutter screw to ensure smooth operation and prevent seizing during repetitive casting cycles.
Mold TL358-158-2R for Precision Hunting, Shooting, and Reloading
90388
LEE TL 2-Cavity Mold specifically engineered for precision casting of .38 Special, .357 Magnum, and .38 Colt New Police caliber bullets. This mold is designed to deliver consistent performance and accuracy for handloaders and ballistic enthusiasts focused on metallic and semi-metallic projectile manufacturing.
Featuring a .358 inch diameter and producing 158-grain 2-Ring Ogival bullets, this mold is optimized for the .38 Special, .357 Magnum, and .38 Colt New Police cartridges, ensuring optimal ballistic coefficients and terminal performance for both target shooting and hunting applications.
Each cavity incorporates a finely engineered micro-groove rifling to enhance bullet lubrication retention, reducing barrel leading and improving overall accuracy during firing cycles.
LEEs 2-cavity molds represent an excellent balance between cost-efficiency and high-quality craftsmanship, making them a preferred choice among precision reloaders and ballistic technicians seeking reliable bullet molds without compromising on durability.
Constructed from corrosion-resistant aluminum blocks, these molds offer superior thermal conductivity compared to traditional iron molds, allowing for faster heat transfer during the casting process. This results in reduced cycle times and improved bullet consistency.
Aluminum mold blocks also weigh approximately one-third less than their iron or steel counterparts, significantly reducing operator fatigue during extended casting sessions and enhancing overall handling ergonomics.
The two halves of the mold are securely clamped together using robust wooden-handled tongs, ensuring zero cavity movement during molten metal pouring and solidification, which is critical for maintaining bullet dimensional integrity and surface finish.
Note that bullet weights may vary slightly depending on the specific lead alloy composition used, allowing reloaders to fine-tune projectile mass to their ballistic requirements.
The included tongs feature ergonomic wooden grips for safe and comfortable handling during high-temperature casting operations.
An integrated, practical sprue cutter blade is incorporated to efficiently sever the lead sprue, facilitating smooth release of fully formed bullets and minimizing post-casting cleanup.
For optimal mold longevity and bullet quality, it is highly recommended to thoroughly degrease the mold before initial use and periodically apply a recommended mold seasoning agent or smoke treatment to enhance release properties.
Never lubricate the interior cavity surfaces of the mold, as this can negatively affect bullet surface finish and dimensional accuracy.
Lightly lubricate the sprue cutter screw to ensure smooth operation and prevent seizing during repetitive casting cycles.
€50.52
Tax included
Related Products
- Out-of-Stock
- Out-of-Stock
- Out-of-Stock
.jpg)
- Out-of-Stock
